![]() From there, it is not that hard to isolate the issue. You can verify this by asking the dealer about the compatibility status of your respective batteries. ![]() While this charger supports a wide variety of batteries, you can still run into some errors down the road if you’re using an off-brand battery. So, you need to narrow down these issues by checking for comparability errors. Most of the time, it is the battery that is behind these errors and not the unit itself. Once that is done, you can try out some of these fixes as well to get everything sorted with the battery as well as the charger. The cables need to be in perfect health for the appropriate battery charging and battery health. That is why you will need to make sure that the cables are in the best of health, and that will ensure perfection for you so you will not have to worry about a single thing at all. To check that, you will need to ensure that you are checking on the battery voltages first, and it should be stable after a few minutes if the battery is deeply discharged.Īfterward, you will definitely need to be checking on the cables and connections and ensure that the cable is not damaged or sharply bent at some point. So, you will need to make sure that you are thoroughly checking on all that and make sure that you are not missing out on anything like that. There are also some other reasons that can increase the battery temperature, and that is definitely not something that you would like to have. You will have to ensure that you are not exposing the battery to direct sunlight or heat, as that can increase the temperature of your batteries. That is why you will need to make sure that you are checking on the temperature first. There can be some other fault with the battery, such as really high temperature on the battery. If the red light is flashing really fast, that could be an indicator that your battery is either deeply discharged, which might be causing you to face the problem. If you would like to know more about the red-light flashing reasons, there can be several different patterns on it as well while the battery is connected to the Battery Tender Jr. This red light on your Battery Tender Jr indicates the microprocessor is working only, and that is all. The exposed pin on a DC cable assembly accessory is connected to NEGATIVE ORĪgain, the same will be true for the exposed pin on the end of anĮxtension cable when the other end of the extension cable is connected to a DC cable assembly accessory.That is something that you will need to be careful about. The same will be true for the exposed pin on the end of anĮxtension cable when the other end of the extension cable is connected to the charger DC output cable.ĭC cable assembly accessories are designed so that the rings, clips, or the cigarette adapter connect to a battery. If the DC cable is directly connected to the body of a charger, then the exposed pin is connected to POSITIVE voltage at the charger output. The following connection rule applies for DC cable assemblies and the black, molded, 2 pin quick- disconnect plug. Each end of the cable extension has a black, molded, 2 pin quick-disconnect plug. The common DC output cable assembly accessories are: (Approx cable lengths 18 inch min, 24 inch max.) Shown in order from left to right: 081-0069-6: Fused Ring Terminal Cable Assembly 081-0069-4: Fused Alligator Clip Cable Assembly 081-0069-5: Fused Cigarette Adapter Cable Assembly Extension cables have the came cord configuration as the DC output cable connected to the charger body. Lengths are DC output cord 10.5 feet + DC Cable Assembly Accessory 1.5 feet (18 inches minimum). ![]() The UL-1236 Standard requires a total of 12 feet from the AC mains wall receptacle to the battery terminals. The approximate DC output cable length is 10.5 feet. That plug connects to a number of DC output cable accessories. ![]() The DC output cord is a 2-wire, insulated cable assembly with a black, molded, 2 pin quick- disconnect plug on the end. There is no ON / OFF switch on the charger. The Battery Tender® Junior charger plugs directly into a residential AC receptacle. Ring Terminals: Approx 5/16" Inside Diameter 9/16" Outside DiameterĪutomotive Style Blade Fuse 3.0 or 7.5 Ampįused Ring Terminals with Quick Disconnect PN 081-0069-6 Quick Disconnect same as used on 081-0069-6 _ Deltran Corporation, 801 International Speedway Blvd., DeLand, FL 32724 Page
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |